Styler Steam Wardrobe with Heat Pump | 5 Hangers, Black

'- (Using tap water) fill the water tank located at the bottom of the Styler. 

- On first use, a full tank of water will be used.

- Discard the water in the drain tank.

- Remove the aroma sheet case located in the bottom left corner of the Styler and insert the scented sheet.

- To prevent clothes from falling off, ensure buttons and zippers are closed after applying to the hangers.

- Place the hangers snugly on the (moving hanger) grooves.

- Press the power button and select the course you want. 

- After selecting the desired course, press the Start button to start the product.

* This content was created for public use and may contain images or details that differ from the product you purchased.

Please install the product in an environment in which the temperature does not fall below 10℃ or exceed 35℃. Environmental temperatures that fall outside of the recommended range can cause performance degradation and/or product malfunction.

Additionally, ensure that the product is installed in a well-ventilated room with at least 20cm upper clearance and 5cm side and rear clearance to the product. To prevent unwanted swaying or vibration during the operation of the moving hanger, install the product on a flat surface. 

Flatness of the product can be adjusted by rotating the front lower legs at the base of the product.

If the product is installed next to a wall, provide at least 5cm side clearance to prevent door collision.

The Styler features patented steam and moving hanger technology to smooth out wrinkles and remove dirt and odor. 

Steam application detaches dirt and odor particles from clothes so that the moving hanger, which moves 350 times a minute, can easily brush them off.

Intertek tests have shown that the [Fine Dust] course removes an average of 99% of fine dust from clothing.

Unlike dry cleaning, the LG Styler cares for clothing without the need for chemicals.

The Styler operates in the following sequence: steam preparation → preheat → refresh (steam application + temperature maintenance) → dry (dry preparation + dry). 

The moving hanger operates from the steam application to the temperature maintenance stage of the refresh cycle, with different operation times and RPMs for each course.

The moving hanger operates for all courses except for the sterilisation and bedding courses, where the shelves are used instead of the moving hanger.

Only thin blankets can be sterilised with the Styler. 

Blankets and comforters weighing 1.5 kilograms (kg) or less should be applied.

If you do not have a blanket hanger, please place the blankets on the shelf. 

Blankets may take longer to dry after sterilisation. (In this case, please use the time selection to allow additional drying).

Shoe materials that are sensitive to steam may be damaged on use.

(Shoes or products containing sponge or adhesive materials may be damaged)

For clean clothes styling, applying shoes is not recommended.

The built-in dehumidifier keeps clothes and indoor spaces dry with the AutoFresh System™. 

An ample 10L capacity water tank removes dampness worries. 

Even with the door closed, air is circulated and dehumidified to keep your wardrobe and living space fresh and pleasant.

If you need to keep your clothes inside the Styler for a long time, try using the Reservation feature. 

Place your clothes in the Styler then press the power button.

Select the course you want, then press the Settings button to use the Reservation feature to set the time you want the movement to complete.

You can set a time from 3 hours to 19 hours, and if you set a time of 5 hours, the selected course will end after 5 hours.

* Do not open the door during operation. Water may drip from the inner walls onto the floor.

* This content was created for public use and may contain images or details that differ from the product you purchased.

Based on the Refresh course, the Styler can be used 3 to 4 times on one full water tank (or 2 times for the Intensive course).

However, on first use, a full tank will be used to fill up the internal steam generator.

Simply fill the water tank when the water refill notification appears. 

The water tank must be filled before use. 

Using filtered water will help the product last longer and perform better.

The tray prevents debris from entering the bottom of the product and protects the instep. (Safety Guard) It also prevents small amounts of condensation that may occur during the steam blast process from dripping on the floor.

Open the Styler door and check the bottom.

Place the dedicated tray down in front of the Styler.

Hook the left hook of the tray onto the lower leg until it clicks into place.

'- Use a soft cloth to remove dust from the inside of the product.

- If the water tank has been left for a long time, water moss may form. Therefore, please clean the inside of the water tank periodically with a cleaning brush.

- If the aroma sheet is not replaced periodically, odor removal and scent performance may decrease.

- Periodically wipe off any accumulated water in the water tank attachment/detachment areas as it may run.

- Empty the tray periodically as accumulated water may gather.

- If the dust filter is clogged, air circulation inside the product may be impaired, resulting in poor performance. Therefore, please clean regularly.