Error codes help identify problems causing your LG dryer to not function properly. Most errors codes on your LG dryer can be resolved easily with a few troubleshooting steps.
If your dryer is showing one of these codes, it indicates that the airflow is restricted somewhere between the dryer and the outside exhaust exit.
While this is typically a signal to have the yearly vent cleaning completed by a professional vent cleaner, here is the list of possible resolutions without a vent specialist.
1. Inside the Dryer
2. Behind the Dryer
3. Outside of the Home
4. Inside the Walls
A nP error code indicates there is no current being detected at the heater. This normally indicates a problem with the electrical wiring in the home.
1. Check power cord connection.
Make sure the power cord is securely plugged into a grounded outlet matching the dryer's rating plate of 240V.
2. Reset the circuit breaker.
From the home's main, turn OFF the dryer's circuit breaker for at least 10 seconds to clear the power surge inside the breaker.
3. Inspect home outlet.
If the nP error is displaying, the home's outlet may need to be checked by a licensed electrician in order to ensure that the correct voltage is supplied to the dryer.
4. Request a Repair.
If the dryer is still not heating at this stage, the unit requires a repair service.
A PS error code on the dryer's display indicates that there is improper voltage with the power cord,
which could be caused by the white and red wire connections being reversed on the dryer's terminal block.
1. Check power cord connection.
Check the power cord installation on the back of the dryer. The videos below explains dryer installation.
2. Reset the circuit breaker.
From the home's main, turn OFF the dryer's circuit breaker for at least 10 seconds to clear the power surge inside the breaker.
3. Verify ground outlet.
Make sure the power cord is securely plugged into a grounded outlet matching the dryer's rating plate of 240V.
4. Request a Repair.
If the dryer is still not heating at this stage, the unit requires a repair service.
A dE error code means that the dryer door is not completely closed. This might be a result of:
1. Reset the unit by unplugging it from power, or trip the circuit breaker.
2. Wait 5 sec.
3. Plug unit back in.
4. Close door firmly.
5. Select any cycle and press Start.
6. If the unit gives the code again, the unit will need service.
An E13 error code on the dryer's display indicates that the drain hose is kinked, crushed, clogged, or that the water in the sump is frozen.
If the E13 error code is showing on the dryer's display:
1. Check that the drain hose is not kinked, twisted, or clogged with water at the end of the hose.
2. If the drain hose was extended, the dryer will not drain well because of the increased resistance. It is recommended to only use the standard LG drain hose.
3. Press the START/PAUSE button to start the dryer again after checking that the drain hose is not kinked, twisted, or clogged.
If the E13 error code occurs again, the unit will require a repair service.
An FO error or a flashing INSERT FILTER on the dryer's display indicates that the lint filter should be checked to ensure that it is inserted properly.
When the lint filter is not inserted properly, the sensor inside the dryer will display FO, and the dryer will stop working.
Remove the lint filter and reinsert it into the lint filter housing.
If the error continues to appear on the display screen, the unit may require a repair service.
HS error code on the dryer's display indicates that the dryer has detected an error with the HUMIDITY SENSOR.
The HS error code will cause the dryer to run for 21/2 hours, which may seem as though the dryer is not drying.
If the HS error is displayed, clean the sensors on the inside of the dryer, located below the lint filter. Allow the sensors to fully dry before attempting another cycle.
If the HS error code persists, the unit may require a repair service.
This usually happens after a power outage. To fix it, we're going to do a factory reset.
1. Unplug the dryer or trip the circuit breaker supplying power to the dryer off.
2. While the dryer is without power, press and hold the Start/Pause button for 5 sec.
3. Restore power and try to run a cycle.
If the PF error code persists, the unit may require a repair service.
A tE1 error code on the display of the dryer indicates a problem was detected with the dryer's thermistor. If the tE1 error code is showing on the dryer's display:
1. Unplug the dryer, or trip the circuit breaker supplying power to the dryer.
2. While the dryer remains without power, press and hold the START/PAUSE button for 5 seconds.
3. Restore power to the dryer and attempt to run another cycle.
If the tE1 error code occurs again after resetting the dryer, the unit may require a repair service.
A tE2 error code on the display indicates a problem was detected with the dryer's thermistor, normally during cold conditions.
A tE2 error code can occur during the SteamFresh™, Steam Sanitary™, or Steam Option, due to the duct cooling down too quickly.
1.Ensure the Lint Filter Is Clean
2. Check the vents for clogs and blockages.
If the tE2 error code occurs again after resetting the dryer, the unit may require a repair service.
The FE error code indicates that the washer is overfilling. This is usually the result of faulty water valve.
1. Close both water taps.
2. In order to drain out any trapped water, power the washer back on, and press the spin speed button until no spin is selected, and press the START/PAUSE button.
3. Once the washer has drained, restart the washing cycle.
If the FE error code persists, the unit will require a repair service.
A gAS error code means that the dryer is not receiving gas.
If the has line is connected properly, not kinked and the valve is ON, the unit will require a repair service.
If your dryer has a child lock button
1. Locate your child lock button. which is usually located on the control panel. It may be labeled differently depending on your dryer model. Look for a lock icon or a button labeled “Child Lock”, “Control Lock” or “CL”.
2. Begin a dry cycle. The child lock function can only be enabled with a dry cycle in progress.
3. Press and hold the [Child Lock] button for 3 to 5 seconds.
4. Once enabled, a “CL” message will appear on your display panel to notify you that the “Child Lock” function is on.
5. To turn off child lock, make sure your machine is powered on and then hold the [Child Lock] button for 3 to 5 seconds.
An Add Water error reading on the dryer's display indicates that there is a water supply error.
Before using a steam cycle, the steam feeder must be filled with water up to the MAX indicator lines. Check the steam feeder to be sure that it is full of water and that the drawer is completely closed.
If the Add Water reading appears on the dryer's display after a cycle has started:
The E5 error code indicates there was a problem with the water supply used for the steam cycle.
If the E05 error code occurs again after resetting the dryer, the unit may require a repair service.
This error code will require service to resolve.
TE4 indicates a problem with the thermistor causing the temperature in the unit to be out of range.
This error code will require service to resolve.
This guide was created for all models, so the images or content may be different from your product.
Your email has been successfully registered.
The restocking notification has already been updated.
Add items to your MY LG wishlist
OTP authentication failed. Please verify your mobile number to use for mobile OTP login.
Split your purchase into equal monthly payments*
* Subject to credit approval
Choose PayPal at checkout and select PayPal Credit.
Representative Example: Assumed Credit Limit £1200 - Purchase Rate 23.9% p.a. (variable) - Representative 23.9% APR (variable).
PayPal Credit is a regulated credit agreement.
LG Electronics U.K. Ltd acts as a credit broker, not a lender.
Borrowing more than you can afford or missing payments may negatively impact your financial position and your ability to obtain credit.
If you fail to make repayments or in certain other circumstances, PayPal may remove your offer, and any outstanding amount will be charged at your standard variable rate.
View full Terms & Conditions and FAQs for PayPal Credit here
